Show older

It's technically past the 24-hour "dry time" window and the finish has lost the ever-so-slightly-rubbery feel it had last evening, but it's still pretty smelly so I'm not going to bring it in and tinker with electronics just yet. (not that it would do me any good without neck/bridge/strings anyway.)

But, I did remember to get a photo of the highly sophisticated bracing I added #cbg

Alright, there's any number of things I *should* do outside today ahead of the impending storm, but what I'm probably *going* to do is see how far I can get on a neck for the #cbg

Slightly better shot of the #cbg box color in the sun, sitting on top of the still-not-finished body of the #telecasterkit

Probably going to splurge on that CB Gitty scarf joint miter box because I don’t have a table saw, and it’s relatively cheap (and the one I tried to make myself is not square, lol.) But with a little filler and sanding this should be close enough.

This test fret was about 100x easier to install than any of the ones I did 15 years ago, and that’s definitely thanks to having the right tools (my wife got me the CB gitty fretting kit for my birthday. #cbg

If I’m going to the trouble of making a scarf joint I might as well add ears so I can give it a nice shape #cbg

Need to clean up the nut slot some but I think I’m ready to start carving? I think the fret slots came out well despite me having to cut half of them using a speed square as a guide because I got ahead of myself and glued the headstock and heel block on like a dingus #cbg

My obsessive nerd inclination is to do some CAD to determine the optimal neck angle per bridge placement and location. I used my ancient, offline copy of adobe Illustrator for basic geometry stuff like this for years and years, but it finally stopped working a couple of OS versions ago and I am not going to let adobe bleed me to death for the rest of my life... but I haven't really learned inkscape or (god forbid) an actual CAD package in the meantime, so that would be a whole yak-shaving expedition that's probably a bit of a moot point anyway because it's not like I have any kind of precision finer than "half a degree-ish" on my saw. 🤷‍♂️

My napkin calculations suggest about 6 degrees, which seems like a lot, but the body *and* neck are smaller than most instruments I'm used to, and math is math.

Worst case I can shim the heel one way or the other. #cbg

5° probably would have been a little better for the neck angle, but I think 6 is close enough that I’ll be able to fine tune the action just by tinkering with the bridge height 😎 #cbg

I had forgotten how pleasing it is to shape a neck, doubly so making little curlicues with the spokeshave.

I spent maybe 5-10 minutes at this this morning and my god it is soothingly meditative

#cbg

:unsure_fry: Not sure if spokeshave difficulties are due to dull blade and inexperience, or spokeshave being a cheap piece of junk. Probably a little of both. (I bought it from Grizzly Industrial and wouldn't have spent more then twenty bucks in 2006 dollars on it)

My sharpening stones are a mess, seeing if I can clean/recondition them is a whole other yak shaving expedition I could go on.

Meanwhile, a cheap rasp worked pretty well to rough out the neck. I got it halfway cleaned up starting with 80 grit sandpaper before the mosquitoes chased me inside... there are still some pretty deep gouges but hopefully sanding will go quickly when I'm not being eaten alive.

Realized a major #footgun: Because my box lid is like 5/8" tall and the neck is only about 1 1/2" deep, my plan to attach the neck with two lag bolts is not going to work.

But, hopefully I can salvage it by putting a notch in the approprate place in the box lid. (I don't think I described the issue very well, but it will be apparent when I photograph that step. #cbg

Ran out of daylight again, but I think it’s just about to the “good enough” stage. Will give it another one more session with 220-grit, and then hit it with some grain filler. #cbg

I had the stain out for the #lm386amp project, so why the hell not. 🤷‍♂️ It will be a little less contrasty against the dark body.

Not sure I’ve ever stained poplar before… not the prettiest wood, at least with this stain. Predictably there are some dodgy spots around the heel where there’s either glue resisting or end-grain/filler soaking up the stain and going dark. Not sure what that resistant spot on the flat part of the heel is from, though. #cbg

...just realized it *probably* would have been optimal to stain after installing frets; I'll have to be super careful cleaning up fret ends and will almost certainly have to do some touching up if I scuff the wood. #cbg

Losing the light and I should let the shellac seal coats I put on the neck dry 100% overnight anyway, but there are a few things I can tinker with on the body.

Tomorrow I’m going to attempt using some dark tinted grain filler on the neck and the #lm386amp cabinet. #cbg

Going to just brush on some black acrylic for a faux headstock and heel cap veneer look #cbg

My working theory is that with a protective layer of tru-oil on the frets that need markers, I’ll be able to glue in some un-stained dowel, cut it flush with a very very good saw I have for such things, and sand it without screwing up the stain #cbg

It was a nice, but not very realistic working theory. It’s fine, it was already looking pretty rustic, and now it’s relic’d. #cbg

Should have drilled the tuner holes before starting the finish, of course. Terrible tear-out despite using a sacrificial block behind. Maybe a poplar thing? The wood seems really fibrous. Time for some more filler (and it will be covered up by the machine heads anyway.) #cbg

:unsure_fry: not sure what’s lack of experience installing frets vs compromising the sharpness of the fret slots by applying finish after cutting them (the grain filler is water based.)

Things seem to be better after doing another pass with the saw to clear debris out of each slot.

With an unradiused fingerboard it seems to me that, once I get all the frets hammered in and filed, I ought to be able to put the entire thing in the jaws of my workmate table to give it a good even press for good measure.

I am going to order a pair of flush-ground nippers right now because I already tell how tedious it’s going to be to file those ends down. #cbg

That went about like I expected, but filing through the stain was actually a very good “ok that’s enough” indicator; making a note to self to use charcoal or chalk on future projects. I’ve gained an appreciation for how forgiving this stain (basic oil-based Minwax “Honey”) is for touch-ups.

All-told the filing and beveling didn’t take more than 30 minutes or so. Should be able to start putting tru-oil on later today. #cbg #lunchbreaklutherie

I’ll be putting one or two more coats in the front of the headstock, but I’m calling the neck done at five (I think, is easy to lose count) coats. The back of the neck looks great. The fingerboard… well, it’s a learning process.

That means I have to get the electronics wired up! I know I ought to let the finish cure for a few days, but could feasibly have this thing strung tomorrow night. 👀 #cbg #lunchbreaklutherie

I got the neck attached, sort of, last night, but I’m not confident it will be strong/stable enough. I may try to re-do it with a banjo dowel-stick sort of arrangement, although without a jig to get that 6° angle just right that will be tricky too. The two complicating factors are the deep box lid, and there just not being enough room or depth in the box to drill a straight hole. #cbg

Well, it’s a bit of a disaster inside but I did the dowel stick thing, deliberately drilling the neck hole a bit large and using epoxy putty to set the dowel at the right angle. The neck is proud of the body by about 1/4, which I’m not thrilled about, but it feels solid.

Definitely not worth the trouble of doing anything other than a through-neck on a #cbg 🙄

I started making a nut from a sample chunk of corian I picked up at Home Depot. Seems like it would work really well, but it’s a little too hard to conveniently sand by hand, and even if I had a belt sander the dust is probably nothing you want airborne without a real dust collection system. I’ll stick to oak. #cbg

That seam on the peghead sure seems more prominent than it did a couple of days ago :unsure_fry:

With my somewhat bungled neck attachment, bridge height is going to be like 7/8” 😣 which will probably be fine, but also silly

I haven’t soldered anything in 20 years and it shows, but this will get the job done. Leaving the pickup taped in place for now, gives me the option to move it later. #cbg

Alright, here goes. Bracing for potential disappointment in the form of catastrophe for structural failure, undetected fretwork problems, etc… #cbg

(So far so good, although I need to re-slot the bridge; thought I’d be able to get away with a *little* wider spacing there despite the untapered neck, but nope)

The pickup is working, it’s a quieter than electromagnetic pickups but that’s cool, it gives me more headroom to play with my amp’s gain and overdrive.

The action feels a little bit high, but that’s a trade-off of not having a truss rod, and part of that is also these monster strings.

Anyway, photos/audio once I get the bridge fixed, and get to know it a little more #cbg

Still trying to get the bridge dialed in, and probably going to try some lighter strings.

But overall, I call it a success, especially in terms of the frets and the intonation.

#cbg

Follow

@mayor woohoo! thanks for sharing the build process, it's been great to watch. Look forward to hearing some music from it :)

· · Web · 0 · 0 · 1
Sign in to participate in the conversation
mastodon.me.uk

Open social media for the UK